2013 Owner's ManualHammer® SHammer 8-Ball®Vegas Jackpot®Vegas 8-Ball®High-Ball®Victory Judge™Victory Boardwalk™
6SafetySafety Terms and Signal WordsThe following signal words and symbols appear throughout this manual and on your vehicle. Your safety and the safe
96SpecificationsTip: Dimensions and specifications may vary with features, options and accessories.VEGAS JACKPOTDimensionsOverall Length 96.3 in (244.
97SpecificationsTip: Dimensions and specifications may vary with features, options and accessories.VEGAS JACKPOTDrive SystemFinal Drive Type Carbon Fi
98SpecificationsTip: Dimensions and specifications may vary with features, options and accessories.VEGAS 8-BALL HIGH-BALL JUDGE BOARDWALKDimensionsOve
99SpecificationsTip: Dimensions and specifications may vary with features, options and accessories.VEGAS 8-BALL HIGH-BALL / JUDGE / BOARDWALKChassisFr
100SpecificationsFuel SpecificationsFor best performance, use only unleaded gasoline with a 91 pump octane minimum (R+M/2 Method).DO NOT USE E85 GASOL
101Maintenance RecordSERVICE PERFORMED COMMENTS MILES(KM)DATE PERFORMED BY
102Maintenance RecordSERVICE PERFORMED COMMENTS MILES(KM)DATE PERFORMED BY
103IndexAAbout the Owner's Manual . . . . . . . . . . . . . . . . . . . 5Accelerating . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
104IndexFFuel Fill Height . . . . . . . . . . . . . . . . . . . . . . . . . . 44Fuel Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . .
105IndexRRear Axle Inspection . . . . . . . . . . . . . . . . . . . . . . 59Rear Brake Pedal . . . . . . . . . . . . . . . . . . . . . . 30, 38Ref
7SafetySafe Riding PracticesImproper use of this motorcycle can result in serious injury or death to you, your passenger and others. To minimize the r
106IndexTThrottle Cable Lubrication . . . . . . . . . . . . . . . . . 62Throttle Control Grip. . . . . . . . . . . . . . . . . . . . . . 29Thrott
8SafetySafe Riding PracticesFollow these general safe riding practices:• Before each ride, perform the pre-ride inspections. See page 32.• Follow all
9SafetySafe Riding Practices• Reduce speed when:- the road has potholes or is otherwise rough or uneven.- the road contains sand, dirt, gravel or othe
10SafetySafe Riding PracticesCarrying a PassengerDo not carry a passenger unless the motorcycle is equipped with passenger seat and passen-ger footres
11SafetySafe Riding PracticesProtective ApparelWear protective apparel to decrease the risk of injury and increase riding comfort.• Always wear a helm
12SafetyGross Vehicle Weight Rating (GVWR)WARNING! Exceeding the gross vehicle weight rating of your motorcycle can reduce stability and handling and
13SafetyCarrying CargoSaddlebagsWhen operating a motorcycle equipped with saddlebags:• Never ride at speeds exceeding 80 MPH (120 km/h). Depending on
14SafetyTransporting the MotorcycleWhen transporting the motorcycle:• Use a truck or trailer. Never tow the motorcycle. Towing will impair steering an
15SafetyAccessory Selection and InstallationUse the following guidelines when choosing and installing accessories:• Do not install accessories that im
California Proposition 65 WarningThis product contains or emitschemicals known to the state ofCalifornia to cause cancer and birthdefects or other rep
16SafetyFuel and Exhaust SafetyGasoline is highly flammable and explosive under certain conditions.• Always exercise extreme caution whenever handling
17SafetySafety MaintenanceFailure to perform safety maintenance as recommended can result in difficult handling and loss of control, which could resul
18SafetyElectromagnetic InterferenceThis vehicle complies with European directive 97/24/EC Chapter 8 requirements, which is equivalent to Canadian ICE
19SafetySafety and Information LabelsDue to different model and market requirements, your vehicle may not have all of the labels shown. Labels that ap
20Component IdentificationHandlebar Area1. Clutch Lever2. Mirror3. Speedometer4. Indicator Light Panel5. Tachometer (if equipped)6. Front Brake Fluid
21Component IdentificationVehicle Identification NumberThe vehicle identification number (VIN) is stamped into the front of the steering head and also
22Component IdentificationEngine Identification NumberThe engine identification number is stamped into the right crankcase half behind the rear cylind
23Instruments, Features and ControlsInstrument ClusterSpeedometerThe speedometer displays vehicle speed in either miles per hour (MPH) or kilometers p
24Instruments, Features and ControlsInstrument ClusterMulti-Function DisplayUse the mode button to toggle through the modes of the multi-function disp
25Instruments, Features and ControlsInstrument ClusterMulti-Function DisplayOdometerThe odometer displays total distance traveled by the vehicle.Trip
The text is printed on 100% recycled with 40% post-consumer waste (PCW).
26Instruments, Features and ControlsInstrument ClusterMulti-Function DisplayAverage Speed (Accessory)The average speed mode displays average vehicle s
27Instruments, Features and ControlsInstrument ClusterMulti-Function DisplayEngine Error CodesThe error screen displays only when the CHECK ENGINE lig
28Instruments, Features and ControlsLeft Handlebar ControlsClutch LeverPull the lever toward the handlebar to disengage the clutch. Gradually release
29Instruments, Features and ControlsRight Handlebar ControlsEngine Stop/Run SwitchPress the top of the engine stop/run switch (STOP) to stop the engin
30Instruments, Features and ControlsFuel CapUse the ignition key to open and close the fuel cap. Follow proper fueling procedures. See page 44.Tip: Pr
31Instruments, Features and ControlsSidestandWARNING! An improperly retracted sidestand could contact the ground during operation and cause loss of co
32Pre-Ride InspectionsAlways perform the recommended pre-ride inspections before each ride. Always perform the inspections before making a long trip a
33Pre-Ride InspectionsElectrical ComponentsMove the ignition switch to the ON position before performing the electrical inspections out-lined on this
34Pre-Ride InspectionsEngine Oil LevelWe recommend the use of only VICTORY brand Semi-Synthetic 20W-40 Motor Oil or an equivalent oil designed for use
35Pre-Ride InspectionsFuel Level1. On level ground, straddle the motorcycle and bring it to the fully upright position.2. Start the engine. The low fu
For your nearest Polaris dealer, call 1-800-POLARISor visit www.polarisindustries.comPolaris Sales Inc., 2100 Hwy. 55, Medina, MN 55340Phone 1-888-70
36Pre-Ride InspectionsTire Pressure1. Check tire pressure before riding, when the tires are cold. This will provide the most accurate reading, as ridi
37Pre-Ride InspectionsFront Brake LeverPull the front brake lever toward the handlebar and release it. It should move freely and smoothly, and it shou
38Pre-Ride InspectionsRear Brake PedalPress and release the rear brake pedal. It should move freely and smoothly, and it should return to its rest pos
39Pre-Ride InspectionsRear Brake Fluid Level1. Remove the right side cover.2. Straddle the motorcycle and bring it to the fully upright position.3. Vi
40Pre-Ride InspectionsMechanical Clutch1. Squeeze the clutch lever toward the handlebar and release it. It should move freely and smoothly, and it sho
41Pre-Ride InspectionsFront SuspensionInspect the front forks for oil leaks or damage, and verify smooth suspension operation. See page 59.SteeringOn
42Pre-Ride InspectionsSidestand1. Straddle the motorcycle and bring it to the fully upright posi-tion.2. Move the sidestand upward to the stored posit
43OperationThe operation section describes how to operate your VICTORY motorcycle to ensure the best performance and longevity of the engine and other
44OperationEngine Break-in PeriodFueling and Fill HeightAlways heed fuel warnings. See page 16. Always refuel on level ground with the sidestand down.
45OperationEngine Break-in PeriodStarting the EngineThe starter interlock system allows the engine to be started only when the transmission is in neut
12013Victory Owner’s ManualHammer® SHammer 8-Ball®Vegas Jackpot®Vegas 8-Ball®High-Ball®Victory Judge™Victory Boardwalk™
46OperationShifting GearsWARNING! Forced shifting (with clutch engaged) could cause damage to the engine, transmission and drive train. Such damage co
47OperationAcceleratingAccelerate by opening the throttle (rolling the throttle control grip rearward). The more quickly you open the throttle, the mo
48OperationParking the MotorcycleChoose a firm level surface to park the motorcycle.1. When fully stopped, shift into neutral.2. Stop the engine.3. Fu
49MaintenanceProper maintenance assures the highest level of safety, durability and dependability for your motorcycle. • Have your VICTORY dealer perf
50MaintenancePeriodic Maintenance TableSee table key belowComponent PageOdometer Reading in Miles (Kilometers)500 (800)5000 (8000)10000 (16000)15000 (
51MaintenanceUniversal ToolThe universal tool and a 4 mm hexagonal wrench are located under the left side cover. The universal tool is a combination 6
52MaintenanceEngine CompressionCheck engine compression periodically to document engine wear and condition. For engine compression check procedures an
53MaintenanceDrive Belt Tension Inspection MaintenanceDrive Belt Deflection - with 10 lbs. (4.5 kg) of forceHAMMER 8-BALLVEGAS 8-BALLVEGAS JACKPOTHIGH
54MaintenanceDrive Belt Tension Inspection1. Elevate and support the rear of the motorcycle with the wheel slightly above the ground. Use an appro-pri
55MaintenanceDrive Belt Tension AdjustmentCAUTION! Make sure the motorcycle is stable when elevated. Injury may occur if the motorcycle tips or falls.
2Copyright© 2012 Polaris Sales Inc. All material in this publication is based on the latest product information at the time of publication. Due to con
56MaintenanceRear Wheel AlignmentWARNING! A skewed rear axle can damage the drive belt, causing belt failure and loss of control of the motorcycle.1.
57MaintenanceRear SuspensionRear Shock Preload (Ride Height) InspectionSet preload with accurate load conditions before riding to ensure optimum handl
58MaintenanceRear SuspensionRear Shock Preload (Ride Height) Adjustment1. Rest the motorcycle on the sidestand. Remove the right side cover. See page
59MaintenanceRear SuspensionSwing Arm and Rear Axle Inspection1. Sit in the operator's seat and slowly bounce the rear suspension a few times. Ma
60MaintenanceFront SuspensionSteering and Front Axle Inspection1. Elevate and support the front of the motorcycle with the wheel slightly above the gr
61MaintenanceFuel SystemCAUTION! Always observe all fuel safety procedures when inspecting or servicing the fuel system. See page 16. Fuel Tank Remova
62MaintenanceThrottle SystemService the throttle system if throttle operation is not smooth, if throttle grip does not return properly, or if cable en
63MaintenanceClutch (Mechanical)Mechanical Clutch Lever Freeplay1. Remove the right side cover.2. While holding the cable, loosen the adjuster lock nu
64MaintenanceGear Shift PedalDo not remove and reposition the shift arm on the shift shaft to adjust gear shift pedal height. A 90°+/-5° angle between
65MaintenanceBrake SystemsFront Brake FluidCheck the front brake fluid level. See page 37. The fluid level should be at or above the top of the sight
3Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Safety . . . . . . . . . . . . . .
66MaintenanceBrake SystemsBrake Lever LubricationLubricate at the intervals recommended in the periodic maintenance table. See page 50.1. Remove the r
67MaintenanceTiresOperating the motorcycle with improper tires or with improper or uneven tire pressure could cause loss of control or accident. Alway
68MaintenanceWheel SpokesInspect both wheels for loose, bent, broken or missing spokes (if equipped). To identify loose spokes, grasp each spoke and t
69MaintenanceSpark PlugsSpark Plug RecommendationsReplace spark plugs at the intervals recommended in the periodic maintenance table. See page 50. Alw
70MaintenanceSeat Removal (HAMMER S)WARNING! A loose seat could cause a sudden shift in riding position, causing loss of control. Always ensure seats
71MaintenanceSeat Removal (JUDGE/BOARDWALK)1. Remove the side covers. Remove the fuse box from the bracket.2. Remove the two screws securing the seat
72MaintenanceSeat Removal (VEGAS 8-BALL/HIGH-BALL)WARNING! A loose seat could cause a sudden shift in riding position, causing loss of control. Always
73MaintenanceHandlebar Position (HIGH-BALL)On models equipped with two handlebar positions, the motor-cycle is manufactured with handlebars in the low
74MaintenanceBatteryThe motorcycle battery is a sealed, maintenance-free battery. Do not remove the battery cap strip for any reason. Keep the battery
75MaintenanceBatteryBattery Installation1. Before installing the battery, make sure it's fully charged and clean.2. Slide the battery into positi
4IntroductionThank you for purchasing a Polaris vehicle, and welcome to our world-wide family of Polaris owners. We proudly produce an exciting line o
76MaintenanceHeadlight Aim InspectionThe top edge of the high beam must be 3 inches (7.6 cm) below the height of the headlight hous-ing parting line a
77MaintenanceHeadlight Lamp ReplacementHigh intensity discharge (HID) lamps, if equipped, should be handled only by a trained tech-nician wearing the
78CleaningMatte Clear Coat FinishesMatte finish products are prone to trapping dirt, oils and other contaminants. Always clean this type of finish wit
79CleaningPure VICTORY ProductsThis section provides tips on the very best way to clean, polish and preserve every surface of your beautiful new VICTO
80CleaningWashing the MotorcycleThere are two totally different styles of motorcycle washing and there is a Pure VICTORY Polish product for each style
81CleaningQuick Clean-UpsFor quick clean-ups between washings, or when water is not available, use Pure VICTORY Spray & Wipe Instant Detailer, a c
82CleaningPolishing the MotorcycleThere are now two totally different styles of polishing or protecting your paint and chrome.Standard Method of Polis
83CleaningPolishing the MotorcyclePremium Polishing for Long-Lasting ProtectionThis newer style of polishing paint and chrome utilizes the latest in h
84CleaningLeather, Rubber and Vinyl CareNever use a non-recommended protectant on seats, footrests, hand grips or tires. Slippery seats, footrests or
85StorageIf you will not operate the motorcycle for several months, such as during the winter, store the motorcycle to prevent damage to the fuel syst
5SafetyAbout the Owner's ManualFailure to follow recommended precautions and procedures could result in severe injury or death. Always heed all s
86StorageBattery Care1. Remove the battery. See page 74.2. Clean oxidation from battery posts and cable connectors with a wire brush. Wash the posts a
87StorageRemoval From Storage1. Remove the cover and any intake or exhaust coverings.2. Unlock the front forks (if locked).3. Verify that tire pressur
88WarrantiesMotorcycle Noise RegulationTampering with noise control systems is prohibited. Federal law prohibits the following acts or causing thereof
89WarrantiesEmissions Control System WarrantyOwner's Warranty ResponsibilitiesAs the motorcycle owner, you are responsible for the performance of
90WarrantiesEmissions Control System WarrantyI. CoverageWarranty defects shall be remedied during customary business hours at any authorized VICTORY m
91WarrantiesEmissions Control System WarrantyIII. Limited LiabilityA. The liability of VICTORY under this Emission Control System Warranty is limited
92WarrantiesVICTORY Motorcycle Warranty PolicyLimited WarrantyVICTORY Motorcycle Division, Polaris Sales Inc., P.O. Box 47700, Hamel, Minnesota 55340-
93WarrantiesVICTORY Motorcycle Warranty PolicyWarranty Coverage And Exclusions:Limitations Of Warranties And RemediesALL IMPLIED WARRANTIES (INCLUDING
94SpecificationsTip: Dimensions and specifications may vary with features, options and accessories.HAMMERDimensionsOverall Length 92.7 in. (235.5 cm)O
95SpecificationsTip: Dimensions and specifications may vary with features, options and accessories.HAMMERDrive SystemFinal Drive Type Carbon Fiber Rei
Komentáře k této Příručce